Expert Answers about Jayco Jay Flight Travel Trailer
- How To Wire etrailer Electric A-Frame Jack With Footplate To 2004 Jayco Jay Flight Travel Trailer
- The etrailer Electric Jack w/ Footplate # EJ-3520-WBX only has one power wire coming out of the jack. It gets its ground connection through the mounting plate which is grounded to the trailer.
You can run the power wire to the coach battery on your 2004 Jayco Jay Flight and attach it to the 12 volt positive terminal. If you do not have a terminal to attach the wire a Ring Terminal # DW05705-1 will give you a 3/8" inner diameter ring to attach to the battery post. The coach battery should...
view full answer... - Cutout Requirements For Furrion RV Electric Fireplace W/ Logs FF34SW15ABL
- The Furrion RV Electric Fireplace with Logs # FF34SW15ABL you were looking at is 33-7/8" wide x 17-3/4" tall x 6-1/4" deep.
The reason the question you mentioned listed 7-3/16" is that when installing it in a cabinet the cut out will need to be 33-3/16" wide x 17-13/16" tall x 7-3/16" deep. If you are installing it in a cabinet you will need to frame the cutout to the wall mount dimensions of 30-9/16" wide x 16-1/4" tall which will is called half flush-mounted and will allow it to work...
view full answer... - Will Brake Controller Show Connected with Pollak 7-Way to RV Socket LED Circuit Tester
- In regards to the Pollak 7-Way to RV Socket LED Circuit Tester part # PK12741, the brake controller may or may not read connected. This will vary from controller to controller but you should still be able to apply the override and see the light illuminate on the tester.
view full answer... - Solera 12V Power RV Awning Conversion Kit Installation Guide
- The Solera 12V Power RV Awning Conversion Kit - Universal - 69" Arms - White Item # LC434724 can be installed by yourself and some friends/family to help with lifting and holding things in place.
The instructions in the kit, that you can also find online by following the link I added, will go over in greater detail how to mount the arms, attaching fabric to the roller tube and connecting it to the arms, and how to wire in the switch to control the arm movement.
view full answer... - Installing Lippert Entry Assist Handle Rail Install that Won't Interfere with Cabinets on Interior
- If you wanted to pull out the pins of the Lippert Entry Assist Handrail part # LC799640 to remove the handle when not in use you certainly could but a better solution might be to test fit the height setting where you install the handle and see if you could mount it in a way that would allow for the clearance you need.
Check out the install video for this for you to check out and see how it installs.
view full answer... - Can Mount-n-Lock SafetyStruts Be Mounted On The Inside Of The Bumper Frame Beam
- Yes, both the Mount-n-Lock SafetyStruts Standard RV Bumper Support Brackets - 4" to 4-1/2" # MO22FR and Universal # MO34VR can be mounted on either the inside of outside of the frame beams. It's typically easier to mount to the outside since you wouldn't have to get under the trailer, but if you're wanting more of a hidden look it's totally acceptable to mount it on the inside.
view full answer... - Speed Rating of Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel
- The speed rating of the Kenda 5.30-12 Bias Trailer Tire with 12" Galvanized Wheel part # AM30790 is 65 mph. That's pretty much the max for a bias ply tire this size but if you switch to a radial like the Taskmaster 5.30R12 Radial Trailer Tire part # TT53012C you can get up to 81 mph. You will have to add the wheel separate though, it's the Steel Spoke Trailer Wheel part # AM20124.
view full answer... - Can Excel RV Tankless Water Heater Be Laid Flat for Installation
- The Excel RV Tankless Water Heater # EX93FR has to be installed in the upright position per the manufacturer. This unit measures 11-1/4" wide x 14-5/8" tall x 5-1/4" deep overall so just make sure you have this room plus a little room for the connections and hoses on the underside and you'll be good to go!
view full answer... - How to Remove Cupholder From Thomas Payne Momentum Recliner
- If you need to remove one of the cup holder assemblies on your Thomas Payne Momentum Recliner you can do so by first locating the notch on the side of the cup holder that you should be able to feel with your hand. Then it's just a matter of using something like a flathead screwdriver to pop up the cup holder using this notch.
Once the unit is popped up from its recessed opening there will be 2 screws revealed that need to be removed before you can completely detach the cup holder wiring...
view full answer... - Installation of SportRack Roof Rack on Jayco Pop-Up Camper for Leak Prevention
- When you install the SportRack Pop-Up Camper Roof Rack - Square Crossbars - Steel # SR1020 on your Jayco Pop-up Camper, I recommend using silicone to seal around the screws to prevent any leaks. I recommend using Loctite RTV 598 High-Performance Silicone Gasket Maker - Black - 2.7-Fl Oz Tube # LT37467 to seal under the towers at the holes and also on top of the brackets at the screw heads.
view full answer... - Do All ST215/75R14 Trailer Tires Use the Same PSI Rating
- For some trailer tires, like the Taskmaster Provider ST215/75R14 # TTWTRTM2157514D, the max PSI is 65 but for others it can be different. Since your tires say max PSI is 50 then that's what you need to set it at. Trailer tire manufacturers tend to have similar specs for different sizes but that doesn't mean there is a "one size fits all" solution especially when it comes to things like PSI and weight ratings. Be sure to note the PSI and weight ratings (as well as the speed rating), fill...
view full answer... - Will the Valterra Replacement Window Frame for RV Entry Doors Turn Yellow Over Time
- Given enough exposure to the sun and elements I'm sure the Valterra Replacement Window Frame for RV Entry Doors # A77006 will eventually turn yellow as would any other white plastic. If you aren't using a cover for when your 2003 Jayco is in storage this would be a huge contributor to the white plastic turning a yellow color over time. By minimizing exposure to the sun and elements though this will help to prolong the white color of the frame plus keep other parts of your trailer in better...
view full answer... - How Is the Mighty Cord 7-Way RV Style Trailer Connector w/ Molded Cable Pinned
- In regards to replacing a trailer connector on a trailer with an option like the Mighty Cord 7-Way RV Style Trailer Connector w/ Molded Cable part # A10-7W8, you need to match wires by function not color. In other words, if there is a green wire on the trailer, you should apply power to that wire to see what light it activates. Then attach this wire to the trailer connector based on the function of the light and how it matches up with the diagram for the trailer connector attached below....
view full answer...
Go To Results